If you’re considering installing a sump pump in your Bloomingdale home, it’s important to know what’s involved. This article will provide information about sump pump installation costs, proper installation of a pump in, and how to maintain your new {de-watering|sump pump|effluent|system. It also discusses the considerations you’ll need to make when choosing a pump.

Cost of installing a sump pump

A sump pump installation can be expensive. There are several factors to consider when considering the cost of installing a sump pump. First, the location is vital. A basement installation typically requires drilling through concrete or partially tearing down finished walls in your basement.  The initial price may seem high, but the money you save over time will be well worth it. Installing a sump pump will protect your home from water damage, and mold growth, and the best way to avoid flooding in your basement.

The cost of a new sump pit installation can range from $1875 to $5000, depending on the type of pump, basement layout, location of the discharge pipe, the number of pumps and pump size(s) required. Typically, the cost to replace a sump pump will be between $200 and $400. A heavier-duty steel, cast iron or stainless steel unit will cost around $300 to $500. Battery backup and water-powered solutions are even more.

Installing a sump pump system is a relatively big project. It involves cutting a concrete hole in your basement floor, installing a sump pump pit liner, and connecting the sump pump to the drain tile. You should be sure the unit is properly sealed with a tight-fitting lid and fully submerged in the new sump pit so that it won’t leak into your basement or crawl space. You will also need electricity close by on a dedicated GFI circuit, preferably.

Once installed, a sump pump will typically last for 7 to 10 years. Some people may need to replace their existing pumps, but this will cost you less than a new installation. The cost of installing a new sump pump is between $575 and $975.

A sump pump installation can be expensive, but a quality sump pump will make your home safer. It will keep water out of the foundation and reduce structural damage.

Steps to install a sump pump in Bloomingdale

Before installing a new submersible sump pump, make sure the area is level and flat. If the pump is in a basement, dig a pit for it. Place a small amount of gravel around the bottom of the pit and make sure the gravel sits flush with the floor. Then, slide the PVC discharge pipe through the hole. Once you’ve secured the pipe, use a hole saw to make the final hole.

Next, make sure to connect the sump pump to a GFCI outlet. Make sure that the pump’s plug is protected against short circuits and fires. If you don’t have experience in electrical wiring, you should seek the assistance of a certified electrician. 

Afterward, place the sump basin just below grade level. Then, you can cut a concrete circle a few inches bigger than the basin’s perimeter and jack hammer it out to get beneath your basement slab and try to reach the water table. 

Depending on the sump pump pit liner used, you can add a fabric liner to keep silt and other debris from clogging the pump. When digging the hole should be at least 6″ deeper than the liner and back filled with gravel.

If you are confident with your skills, can handle basic plumbing tasks, and are prepared to do a little hard work, you can install a new sump pump in a few hours.

Considerations for installing a sump pump in a Bloomingdale crawl space or basement

If your house has a low-lying patio, you may need to install a sump pump to prevent flooding and the accumulation of water and debris. There are several types of sump pumps available to suit your needs. 

We prefer to use submersible pumps, powered by an electrical outlet or battery, that sits in the pit under the water level and pushs the water and debris (up to 1/2″ solids) out of the sump pit. These pumps are workhorses and are cooled by the water allowing them to run constantly when necessary

The best time to install a sump pump in your basement or crawl space is before you experience flooding. Left unprotected water can accumulate and damage your home’s foundation, leading to costly repairs. Additionally, the increased moisture level can lead to mold and wood rot, affecting the air quality inside your home. A sump pump not only prevents flooding, but it also helps keeps your home’s interior dry and safe.

Another important factor to consider is the location of the pump’s discharge line. It should be located far enough away from your house to prevent it from recycling back into your basement. We prefer to install the line underground with a pop up cover, but of course this is more labor-intensive. Putting the line underground also prevents a tripping hazard and mowing/weed whacking inconvenience.

Before installing a sump pump in your crawl space, it is crucial to determine the cause of the problem. For example, a clogged sewer pipe might allow groundwater to seep into your crawl space. An over-saturated soil could also lead to excessive amounts of groundwater.

There are different kinds of sump pumps to choose from. Some are lesser quality and lightweight, while others are built to last. The price of a sump pump can range from $650 to $5,000 with the cost of labor varying depending on your particular installation. With the proper tools and know-how, it is a DIY project, but you may prefer to hire the experts at Sump Pump Gurus to do it for you.

Maintenance of your Bloomingdalesump pump

Regular maintenance is an essential part of sump pump installation. Sump pump maintenance is not difficult and is easy to perform yourself or by the professionals at Sump Pump Gurus. It is important to clean and inspect the sump pump, check for rust or debris, and lubricate the bearings (in lower quality non-sealed systems). 

Check the pump’s discharge pipe for debris, and plug it into a power outlet. Then, fill the basin with water to allow the pump to run properly. Check the discharge pipe for proper operation quarterly, and make sure the water is flowing freely.

Clean the sump pump by using a hose, a stiff brush, and a sponge. You can also use a diluted vinegar or a bleach solution to clean the pump. While cleaning, inspect for corrosion, or iron ochre. If you notice resistance when running the pump, it might be a sign of buildup near the connection site. If severely clogged, you may need to have the discharge line snaked or replaced.

Check the size of the pump’s pit to ensure that it is large enough for it to function efficiently. The pump should also have a functioning check valve to prevent water from flowing back into the pit if the pump is turned off. Lastly, always check the backup power source of the sump pump.

The main components of the pump are the electrical connection, the water intake and discharge pipe, and the switch mechanism. Make sure the pump’s discharge pipe is clean and free of any obstructions. Also, make sure the pump’s discharge pipe is properly connected to a drain or basin. 

A clogged discharge pipe can cause the pump to stop working. If your sump pump is vibrating continuously, it could be undersized or wearing out. A clogged discharge pipe will cause backflow, which can cause the sump pit to fill again and create pressure on the pump that can cause it to burn out early.

During flooding events, sump pumps can drain large amounts of water. Some models can handle as much as four or five thousand gallons of water per hour. Whether you have a broken water line or a large rainfall, sump pumps are a necessity to prevent serious damage to your home.